HDYRAULIC HOSE PIPE EN 8564SH WIRE SPIRAL REINFORCEMENT
| Tube: | Nitrile |
| Reinforcement: | Two braids of high-tensile steel wire. |
| Cover: | Neoprene. |
| Temperature range: | - 40ºC to + 100ºC |
Part
|
In | Hose Size ID DIN Dash | Hose OD | Max.Working pressure | Min.Bend Radius | Min..burst pressure | Weight (ibs/foot) |
| In | mm | pai | Mpa | In | mm | pai | Mpa |
| G4SP-04 | 1/4 | 6.4 | 0.705 | 17.9 | 6500 | 45.2 | 6 | 152 | 26200 | 180.6 | 0.3853 |
| G4SP-06 | 3/8 | 9.5 | 0.843 | 21.4 | 6450 | 44.5 | 7 | 176 | 25800 | 177.9 | 0.4985 |
| G4SP-08 | 1/2 | 12.7 | 0.969 | 24.6 | 6000 | 41.4 | 9 | 229 | 24000 | 165.5 | 0.5869 |
| G4SP-10 | 5/8 | 15.9 | 1.11 | 28.2 | 5000 | 34.5 | 10 | 254 | 20000 | 137.9 | 0.9661 |
| G4SP-12 | 3/4 | 19 | 1.268 | 32.2 | 5000 | 34.5 | 12 | 305 | 20000 | 137.9 | 0.9661 |
| G4SP-16 | 1 | 25.4 | 1.563 | 39.7 | 4000 | 27.6 | 13.5 | 343 | 16000 | 110.3 | 1.3273 |
Hose in the use and design should pay attention to the following matters
The bending radius should not hose is too small, the general should not be less than < hydraulic hose
assembly features Technical Regulations > in the value.
The hose assembly shall be a straight part connected with a pipe joint, two times the length of the pipe
diameter should not be less than
2. The length of hose assembly, hose should be taken into account in the oil pressure, length contraction
deformation will occur, the general contraction for length 3 ~ 4%. so the hose assembly is installed, is not
allowed in a tight state.
3, the hose assembly should be installed to ensure no torsional deformation. The joint axis of the tube
should be placed in the plane. To avoid damage to each other during exercise.
4 ends of hose, hose should avoid contact and friction with the sharp corners of the mechanical parts, to
avoid pipe damage
1, pressure hose specified working pressure is usually not less than the maximum pressure of the
system, not only in constant use, allowed increased by 20%; for the frequent use, often to reduce the
torsional shock pressure 40%. system if higher than the specified working pressure hose, not only
reduces the service life of the hose, and may lead to people accidents.
2, temperature, fluid temperature and ambient temperature, whether it is stable or transient, shall exceed
the temperature limit of the hose, the recommended temperature is lower or higher than the hose, hose
can reduce the performance caused by the hose is damaged, causing leakage.
3, fluid compatibility: fluid in the hose. Product samples shall comply with the "use" made in the
regulations, beyond the prescribed use can not guarantee that the service life and the safety of the pipe.
At the end of
4, the appropriate connection: as the nut is connected The utility model has the advantages of convenient
operation and low cost, and is widely used, but when the vibration is large, the nut loosening problem is
taken into account.
Product Tags:
|
|
Hdyraulic Hose Pipe EN 8564sh High Pressure Rubber Hose Oil Resistant Images
|
